| 1 |
|
Electrical panel set consisting of the following: |
| |
A |
Electrical panel (1) |
| |
B |
One (1) parallel switch for emergency engine/house battery paralleling |
| |
C |
Engine battery shut off switch and panel |
| |
|
|
| 2 |
|
Shore power inlets & AC system per PAE design #N47ACS-4700 |
| |
A |
Marinco #6373EL stainless steel 50amp 3 pole 4 wire 120/240VAC 60 HZ |
| |
B |
Marinco #303SSEL stainless steel 30 amp 2 pole 3 wire 120VAC 60 HZ |
| |
C |
Olsun isolation transformer SGS 12 YY-0-15 |
| |
D |
Olsun balancing transformer SGS 7.5 HD-2-316 SS |
| |
E |
All galley and head outlets to be GFCI protected. |
| |
|
|
| 3 |
|
Battery and DC system per PAE design #N47DCS-4700 |
| |
A |
4 x 255+ AH (8D) Lifeline batteries for house appliances (510 amp hours) and two additional 4Ds for 24v engine starting. The engine starting batteries are isolated from the house batteries, preventing inadvertent discharge of the engine starting battery. The main engine has dual alternators (1 x 175 amp 24v large case for charging house bank and 1 x 40 amp 24v for charging engine batteries). Parallel switches provide for emergency engine starting |
| |
B |
A group 31 Lifeline battery with 20 amp 12v charger to be installed in pilot house for any 12v needs. There will be 12v section on the DC panel for optional 12v breakers. |
| |
C |
Each battery secured with stainless steel tiedown beams |
| |
|
|
| 4 |
|
Battery cable: to be "00" for general battery leads with "0000" for starting and optional bow thruster |
| |
A |
Positive lead to be red |
| |
B |
Negative lead to be black |
| |
|
|
| 5 |
|
All wiring used throughout boat to be color coded - all wire supplied by factory to be tinned wire |
| |
|
|
| 6 |
|
Conduits for future installations |
| |
A |
PVC from mast step to pilothouse |
| |
B |
PVC from engine room to pilothouse |
| |
|
|
| 7 |
|
Radio ground plane (optional) |
| |
|
|
| 8 |
|
Electrolytic control: |
| |
A |
All thru hulls to be bonded together with a #6 green wire and tied into the 24 volt DC ground system |
| |
B |
All hardware mounted below waterline i.e. stuffing box, stern bearing housing, rudder shoe, rudder frame, rudder stuffing box to be grounded into bonding system |
| |
C |
3 x 2-1/2" x 5-3/4" (5.08cm x 14.6cm) zinc plates tied into the bonding system |
| |
|
|
| 9 |
|
A.C. Generator (optional) |
| |
A |
Foundation to be provided within the engine room to accommodate up to a 16 KW generator |
| |
B |
Electrical panel to accommodate AC ship's power |
| |
|
|
| 10 |
|
4kw, 24v inverter / charger with remote panel |
| |
|
|
| 11 |
|
Inverter bypass switch located near inverter for use if inverter should fail. |
| |
|
|
| 12 |
|
TV/phone inlet Marinco #PH6592TV-SS phone wired to pilothouse and owner's cabin. TV wired to salon TV locker and owner's cabin |
