| All horizontal surfaces on deck to have Gibco non-skid pattern as shown in deck plan - standard non skid to be a contrasting color to parameter deck |
|
| Stainless 316 handrails 1-1/4" (3.2 cm) diameter with electro-polished bases. All rails shown on PAE drawings to be standard in addition to those specified |
| Transom hand rails |
| Hand rails along port and starboard side deck coamings |
| Rail on underside of aft deck overhang |
| Rail around flybridge sink console |
| Rail at stairs going up from side deck to Portuguese bridge |
|
| Stainless steel 316 Hawse fittings: Four (4) starboard side and three (3) port side per drawing 5" x 10" (12.7 cm x 25.4 cm) with cleats. Recessed into bulwarks where possible. One (1) on aft center line with cleat |
|
| Bollard: Aritex # A251Type 400 S/S 316 bollard, one (1) centerline aft of windlass per drawing |
|
| Upper rub rail cap to be 316 stainless steel 2-1/2" w x 7/16" thick (6.4 cm w x 1.1 cm thick) fastened with flush 316 stainless steel fasteners. Stainless steel caps on upper and lower rub rails as shown in design |
|
| Lower rub rail cap to be 316 stainless steel 1-1/2" w x 5/16" thick (3.8 cmwW x 7 mm thick) |
|
| Manship stainless steel oval ports in hull and deck as shown on design. Ports positioned as follows: |
| Four (4) starboard side hull 8" x 16" (20.3 cm x 40.6 cm) oval |
| Four (4) port side of hull 8" x 16" (20.3 cm x 40.6 cm) oval |
| All opening ports to be fitted with screens and deadlights |
| Storage garage - one (1) |
| All lower level port lights will be fixed (non-opening) |
|
| Stainless steel 316 double bow roller - rollers to be slotted for chain. Roller to be built per PAE design |
|
| Stainless steel 316 bow pulpit, rails and stanchions to be 1-1/4" (3.2 cm) diameter. Bow pulpit to have socket for 1" (2.5 cm) burgee staff. Bases to be round with fastening stud welded on bottom, except upper deck which will be fastened with flat head screw |
|
| Foredeck to have solid 316 stainless rail with lifeline in middle section. Lifeline to be 5/16" (7 mm) diameter 1 x 19 stainless steel wire without vinyl coating, with 1-1/4" (3.2 cm) diameter stanchions. Bases to be round with fastening stud welded on bottom. All bases to have drain holes on bottom |
|
| Windshield Wipers: "Exalto" four (4) 2-speed self-parking motor, with wash system for four (4) front windows |
|
| Horn: Kahlenberg dual trumpet # DO-A chrome finish with 24 volt compressor/tank kit # P449-4 and 24 volt solenoid valve kit # V-69-K located on top of stack |
|
| Deck hatches: Per deck plan, four (4) Lewmar: Two (2) x # 60 "Ocean Series" and two (2) x # 70 "Ocean Series" to include ocean air insect and privacy screens |
|
| Access to flybridge from wheel house through PCM door/hatch |
|
| Windows to be Pacific Coast Marine with 1/2” (1.27 cm) thick tempered glass |
| All side windows to be tinted glass |
| Three wheel house opening windows to be Pacific Coast Marine with insect screens. Port side starboard side and port aft |
| All salon windows to be recessed 1" (2.5 cm) |
|
| Aluminum doors by Pacific Coast Marine as follows (Note: interior as well as exterior PCM doors are included in this schedule): |
| Wheel house - Two (2) each, "Weather Tight" Dutch door, one (1) left hand mortise hinge, one (1) right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.3 cm) |
| Salon aft - one (1) each, "Weather Tight" double door, main opening on left side, mortise hinges. C.O. 48" x 73" (121.9 cm x 185.4 cm) |
| Salon starboard side - one (1) each, "Weather Tight" Dutch door, right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm) |
| Salon port side - one (1) each, "Weather Tight" Dutch door, right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm) |
| Engine room -one (1) each, water tight # PCM4170-W with sound blanket core, painted. Right hand surface mount hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm) |
| Lazarette - one (1) each, with port hole, "Water Tight"# PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 46" (53.3 cm x 116.8 cm) |
| Storage garage on starboard side |
|
| Boarding doors: port and starboard - opening in two pieces. Top to fold up and over and bottom to open outboard. Stern doors per drawing. Doors to have Aritex stainless steel "blind" dog lock/handles |
|
| Davit: Steelhead SM2500 - 2500 lb (1,134 kg) capacity hydraulic standpipe davit with boom extension from 10' to 14' (3.05 m to 4.27 m) mounted on port aft side of boat deck per drawing. Davit sized and positioned to launch dinghies from port side and transom |
|
| Aft deck exterior cabinet |
| Sink: stainless steel to drain directly overboard |
| Faucet: Aft deck faucet is folding faucet. "Scandvik" # MR4550 |
| Control alcove for DDEC engine control ABT bow and stern thruster jog levers, start/stop, air horn push buttons and forward windlass control |
| Settee with vinyl cushions and three (3) free standing teak chairs |
| Ladder to boat deck |
| Console on port side for storage |
|
| Bottom treatment: Three (3) layers of epoxy barrier coat and three (3) coats of anti fouling paint |
|
| Upper deck to drain through scuppers 2" (5.08 cm) diameter |
|
| Anchor well to drain through scupper 2" (5.08 cm) diameter |
|
| Port and starboard storage lockers in Portuguese bridge |
|
| FRP exhaust stack/radar mast with flag halyards port and starboard per PAE design |
|
| Portuguese bridge control stations port and starboard side of forward Portuguese bridge. Station to be recessed into Portuguese bridge with enough room for DDEC control, bow and stern thruster controls, start/stop and horn. Recess to have courtesy light inside |
|
| Flybridge per PAE design, sink, Norcold # DE-0051 drinks refrigerator, and one (1) Stidd "Slimline" helm chair # 500N-2x2 white vinyl and settee with vinyl cushions and high gloss teak table. Sink to drain directly overboard. Ritchie SS 5000 compass installed |
|
| Stern capstan winch: One (1) Maxwell VC 2200 24 volt per PAE design |
|
| Flag staff: 48" (122 cm) teak flag staff with socket for aft cap rail |
|
| Door to foredeck through Portuguese bridge with Aritex stainless steel dog set |
|
| Anchor: 300 lb. (136 kg) stainless steel plow |
|
| Chain: 400' of 1/2" HT (122 m of 1.27 cm HT) chain |
|
| Swim ladder: Stainless steel with teak steps mounted on swim step |
|
| Cleats: Two (2) pop-up style 10" (25.4 cm) cleats on swim step port and starboard for dinghy tie up |
|
| Windlass: Maxwell VWC 4500 hydraulic with band brake and 1/2" (1.27 cm) HT chain gypsy |
|
| Maxwell chain stopper for 1/2" (1.27 cm) diameter HT chain |
|
| All exterior locker doors to use stainless steel flush latches |
|
| All exterior locker doors to have stainless steel louvered vents |
|
| All exterior door keepers to be ABI # 2039CH |
|
| Two (2) Fishing pole holders flushed into bulwarks in cockpit. One each port and starboard sides with drains |
|
| Stainless steel stem plate with anchor wash nozzle and Nordhavn emblem |
|
| Large pad eye at stem through boot top |
|
| Three (3) "U" shaped rails across swim step |
|
| Nordhavn name plates x two (2) port and starboard side per PAE design |
|
| 40 Gallon (151.42 liter) gasoline storage tank with electric pump installed in a FRP box on the upper deck |
|
| "Flopper Stopper" system for use at anchor. System to include folding poles port and starboard with associated rigging and two Prime "wing" type flopper plates |
