1.		All Horizontal Surfaces on Deck to have a diamond pattern non skid as shown in deck plan - standard non skid to be a contrasting color to parameter deck
	A.	Lower Aft Deck and Side Decks to have 1/2" (1.27 cm) thick teak overlay
2.		Stainless 316 Handrails 1-1/4" (3.2 cm) diameter with electro polished bases.
	A.	N57 style transom hand rails
	B.	N57 style hand rails along port and starboard side deck coamings
	C.	N57 style rail on underside of aft deck overhang
	D.	Rail around F/B sink console
	E.	41" (104.1 cm) Rails at stairs going up from side deck to P/B to be recessed
	F.	Vertical handrail on the port and starboard boarding doors
3.		Nine (9) S/S 316 Hawse Fittings: Eight (8) P&S per drawing 5" x 10" (12.7 cm x 25.4 cm) with solid SS cleats. Recessed into bulwarks where possible. One (1) on aft center line with cleat (Cleats to be solid S/S Bar).
4.		Two (2) S/S 316 Bollards centerline aft of windlass
5.		Upper Rub Rail Cap to be 316 stainless steel 2-1/2" W x 7/16" thick (6.35 cm W x 1.11 cm thick) fastened with flush 316 stainless steel fasteners. Stainless steel caps on upper and lower rub rails as shown in design.
6.		Lower Rub Rail Cap to be 316 stainless steel 1-1/2" W x 5/16" thick (3.8 cm W x 7.94 mm thick)
7.		Manship Ports in Hull and Deck. Ports positioned as follows:
	A.	Seven (7) starboard side hull 8" x 16" (20.32 cm x 40.6 cm) oval; (three (3) opening and four (4) fixed)
	B.	Six (6) port side of hull 8" x 16" (20.32 cm x 40.6 cm) oval; (two (2) opening and four (4) fixed)
	C.	All opening ports to be fitted with screens and deadlights
8.		Stainless Steel 316 Double Bow Roller - rollers to be slotted for chain. Roller to be built per PAE design 76-00-BR.
9.		Stainless Steel 316 Bow and Stern Pulpits and stanchions to be 1-1/4" (3.2 cm) diameter. Bow pulpit to have socket for 1" (2.5 cm) burgee staff. Bases to be round with fastening stud welded on bottom, except upper deck which will be fastened with flat head screw.
10.		Foredeck to have solid 316 stainless rail with lifeline in middle section. Bases to be round with fastening stud welded on bottom. All bases to have drain holes on bottom.
11.		Windshield Wipers: "Exalto" two (2) speed self-parking motor, with wash system for five (5) front windows
	A.	#EX2167.32 wiper motor 223BS 24 volt/23Nm, for (1- 3/8” ) bulkheads x five (5)
	B.	#EX2133 T1 Pantograph arm 10.6" -17.7" (270-450 mm) adjustable x five (5)
	C.	#EX2171 curved wiper blade 16" (400 mm) x five (5)
	D.	#EX2159 Combo switch for single wiper 24v x five (5) (custom engraved panel per PAE design)
	E.	#EX2143 24volt solenoid valve for wash system x one (1)
	F.	#EX2133.03 tubing retainer strip x five (5)
	G.	#EX2184 Washing Jet for type 1 adjustable pantograph arm x five (5)
	H.	#EX2186 plastic bulkhead connector for 19.7" (500 mm) - new style
	I.	#EX2154 Tubing 1/4” (6.35 mm) soft black x 5 meters
	J.	#EX2157 Tubing 1/4" (6.35 mm) hard black for push fit plumbing fittings x 5 meters
	K.	#EX2129 elbow 6 x 24" x six (6)
	L.	#EX2166 T-coupling 6x6x6mm x four (4)
	M.	#EX2119 straight coupling , 1/4” (6.35 mm) x one (1)
12.		Horn: Kahlenberg dual trumpet #D-1 with white finish.
13.		Deck Hatches: Per deck plan, one (1) Lewmar #70 "Ocean Series" to include insect and privacy screens. Two (2) Lewmar #50 "Ocean Series" to include insect and privacy screens.
14.		Dorade Vents: Two (2) to have FRP box with standard TS style 316 SS cowl vent inside painted white and to be positioned per PAE deck plan
15.		Access to F/B From Wheel House thru hinged cockpit hatch custom built by PCM.
16.		Windows by Pacific Coast Marine with 1/2" (1.27 cm) thick laminated tempered glass.
	A.	All side windows to be tinted glass
	B.	Two wheel house opening windows to be PCM with insect screens
	C.	All salon windows to be recessed 1" (2.5 cm).
17.		Aluminum doors by Pacific Coast Marine as follows (Note: interior as well as exterior PCM doors are included in this schedule):
	A.	Wheel house--Two (2) ea. Weather Tight Dutch door, one (1) L.H. Mortise hinge, one (1) R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)
	B.	Salon after--One (1) ea. Weather Tight Sliding door. 54" x 73" (137.2 cm x 185.4 cm).
	C.	Salon starboard side--One (1) ea. Weather Tight Dutch door, R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)
	D.	Engine room--One (1) ea, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm).
	E.	Lazarette--1ea, with port hole, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 46" (53.3 cm x 116.8 cm)
	F.	Bilge bulkhead between station 2 - 3, and bulkhead at station 1. Two (2) ea Water Tight doors, R.H. surface mount hinge. Painted.
	G.	Please not that the weather tight doors are to have mortise hinges. The watertight doors are to have surface mounted hinges.
18.		Boarding Doors: port and starboard - opening in two (2) pieces. Top to fold up and over and bottom to open outboard. Stern door on starboard side aft per drawing. Doors to have Freeman "blind" dog lock/handles.
19.		Davit Marquipt 2500 LB (1134 kg) capacity hydraulic/240VAC davit with extendable boom to 21' (6.4 m) mounted on port aft side of boat deck per drawing. Davit sized and positioned to launch dinghies from port side and stern.
20.		Aft deck Exterior Cabinet
	A.	Sink: S/S to drain directly overboard
	B.	Faucet: Shurflo #133-0210-CP
	C.	Control alcove for DDEC engine control ABT bow and stern thruster jog levers, start/stop, air horn push buttons and forward windlass control
21.		Bottom Treatment: Three (3) layers of epoxy barrier coat and three (3) coats of anti fouling paint
	A.	Two (2) coats of antifouling to be applied at Ta Shing and one (1) coat to be applied after the boat is hauled out at Kaohsiung before shipment
22.		Upper Deck to Drain through six (6) 2" (5.1 cm) scuppers three (3) per side.
23.		Anchor Wellto Drain through scupper 2" (5.1 cm) diameter
24.		Port and Starboard Storage Lockers in Portuguese bridge with FRP louvers
25.		FRP Exhaust Stack/Radar Mast with flag halyards port and starboard
26.		Portuguese Bridge Control Stations port and starboard side of forward P/B. Station to be recessed into P/B as on N57 with DDEC control, bow and stern thruster controls, start/stop/horn. Recess to have courtesy light inside.
27.		Flybridge with FRP Hardtop, sink, U-Line #CO2175FFS drinks refrigerator, and two (2) Stidds "Slimline" helm chairs #500n-2x2 white vinyl and settee with vinyl cushions and high gloss teak table. Sink to drain directly overboard. Ritchie #SS 5000 compass installed on FRP pad.
	A.	FRP hardtop finished with smooth Gelcoat, With white non-skid
	B.	Hardtop to have a stainless rail continuation of the ladder on the topside of the hardtop to allow a person to easily access this area.
	C.	Flybridge to have four (4) freeing ports, two (2) port and two (2) starboard
28.		Stern Capstan Winches: Two (2) Maxwell VC 2200 24v port and starboard
29.		Flag Staff 48" (121.9 cm) with socket for aft cap rail
30.		Door to Foredeck through Portuguese bridge with freeman dog set
31.		Freeman Watertight Deck Hatch over chain locker, #18HAALR x 2. .
32.		Anchor: Airtex 300 lb. (136 kg) stainless steel Plow x 2
33.		800'-1/2" Chain (243.8 m - 1.27 cm) HT in two (2) 400' (121.9 m) lengths from port and starboard chain lockers
34.		Swim Ladder: Stainless steel with teak steps mounted on swim step under an FRP hatch.
35.		Two (2) Pop-up Style 10" Cleats on swim step port and starboard for dinghy tie up
36.		Windlass: Maxwell VWC 4500 hydraulic with band brake and 1/2" (1.27 cm) HT chain gypsy x 2
37.		Maxwell Chain Stopper for 1/2" (1.27 cm) diameter HT chain x two (2)
38.		All Exterior Locker Doors to use "Perko" fig. 777 flush hatch dogs as latch
39.		All Exterior Locker Doors to have FRP louvered vents
40.		All Exterior Door Keepers to be ABI #2039CH
41.		Two (2) Fishing Pole Holders flushed into bulwarks in cockpit. One (1) each port and starboard sides with drains
42.		Stainless Steel Breast Plate with two (2) anchor wash nozzles and Nordhavn emblem
43.		Large Pad Eye at stem through boot top 1-1/4" (3.2 cm) OD
44.		Life Ring Port and Starboard Side of wheel house in recess
45.		Four (4) "U" Shaped Rails across swim step
46.		Nordhavn Name Plates x two (2) port and starboard side per PAE design
47		All Deck Washes to be installed in recessed TA Shing made FRP boxes with FRP doors.
48		Foredeck Lockers, three (3) total: two (2) flush style port and stb.and one (1) on centerline fwd. of P/B. Centerline locker to have gas shocks to hold open.
49		80 Gallon (303 liter) Gasoline Storage Tank with electric pump installed in a FRP box on the upper deck.
50		"Flopper Stopper" System for use at anchor. System to include folding poles P&S with associated rigging and two (2) Prime "wing" type flopper plates.
51		Zincs
	A.	Ship loose two (2) left hand shaft zincs and two (2) right hand shaft zincs
	B.	Ship Loose four (4) B4 plate zincs