| 1. |
|
All Horizontal Surfaceson Deck to have a diamond pattern non skid as shown in deck plan - standard non skid to be a contrasting color to deck parameter |
| |
|
|
| 2. |
|
Stainless 316 Handrails 1-1/4" (3.18 cm) electro polished bases. |
| |
A. |
N57 style transom hand rails |
| |
B. |
N57 style hand rails along port and starboard side deck coamings |
| |
C. |
N57 style rail on underside of aft deck overhang |
| |
D. |
Rail around F/B sink console |
| |
E. |
41" (104.1 cm) Rails at stairs going up from side deck to Portuguese Bridge are recessed |
| |
F. |
Vertical handrail on the port and starboard boarding doors |
| |
|
|
| 3. |
|
Nine (9) S/S 316 Hawse Fittings: Eight (8) P&S 5" x 10" (12.7 cm x 25.4 cm) with cleats. Recessed into bulwarks where possible. One (1) on aft center line with cleat (Cleats to be solid S/S Bar). |
| |
|
|
| 4. |
|
Two (2) S/S 316 Bollards centerline aft of windlass |
| |
|
|
| 5. |
|
Upper Rub Rail Cap to be 316 stainless steel 2-1/2" W x 7/16" thick (6.35 cm W x 1.1 cm thick) fastened with flush 316 stainless steel fasteners. Stainless steel caps on upper and lower rub rails. |
| |
|
|
| 6. |
|
Lower Rub Rail Cap to be 316 stainless steel 1-1/2" W x 5/16" thick (3.81 cm W x 1.1 mm thick) |
| |
|
|
| 7. |
|
Manship Ports in Hull and Deck. Ports positioned as follows: |
| |
A. |
Six (6) starboard side hull 8" x 16" (20.3 cm x 40.6 cm) oval (4 opening and 2 fixed) |
| |
B. |
Six (6) port side of hull 8" x 16" (20.3 c, x 40.6 cm) oval (4 opening and 2 fixed) |
| |
C. |
Lower cabin portlights to be non-opening type |
| |
|
|
| 8. |
|
Stainless Steel 316 Double Bow Roller - rollers to be slotted for chain. |
| |
|
|
| 9. |
|
Stainless Steel 316 Bow and Stern Pulpits and stanchions to be 1-1/4" (3.18 cm) diameter. Bow pulpit to have socket for 1" (2.5 cm) burgee staff. Bases to be round with fastening stud welded on bottom, except upper deck which will be fastened with flat head screw. |
| 10. |
|
Foredeck to have solid 316 stainless rail with 1-1/4" (3.18 cm) diameter stanchions. Bases to be round with fastening stud welded on bottom. All bases to have drain holes on bottom. |
| |
|
|
| 11. |
|
Windshield Wipers: "Exalto" two (2) speed self-parking motor, with wash system for five (5) front windows |
| |
A. |
#EX2167.32 wiper motor 223BS 24 volt/23Nm, for (1- 3/8” ) bulkheads x five (5) |
| |
B. |
#EX2133 T1 Pantograph arm 10.6" -17.7" adjustable x five (5) |
| |
C. |
#EX2171 curved wiper blade 16" x five (5) |
| |
D. |
#EX2159 Combo switch for single wiper 24v x five (5) |
| |
E. |
#EX2143 24volt solenoid valve for wash system x one (1) |
| |
F. |
#EX2133.03 tubing retainer strip x five (5) |
| |
G. |
#EX2184 Washing Jet for type 1 adjustable pantograph arm x five (5) |
| |
H. |
#EX2186 plastic bulkhead connector for 19.7" (50 cm) - new style |
| |
I. |
#EX2154 Tubing 1/4” (6.35 mm) soft black x 5 meters |
| |
J. |
#EX2157 Tubing 1/4” (6.35 mm) hard black for push fit plumbing fittings x 5 meters |
| |
K. |
#EX2129 elbow 6x.24" x six (6) |
| |
L. |
#EX2166 T-coupling 6x6x6mm x four (4) |
| |
M. |
#EX2119 straight coupling , 1/4” x 1 (6.35 mm x 2.5 cm) |
| |
|
|
| 12. |
|
Horn: Kahlenberg dual trumpet #D-1 with white finish |
| |
|
|
| 13. |
|
Deck Hatches: Per deck plan, five (5) Lewmar #70 "Ocean Series" to include Oceanaire insect and privacy screens. One (1) Lewmar #30 "Ocean Series" to include Oceanaire privacy shade and insect screen. |
| |
|
|
| 14. |
|
Aft Upper Deck Seating Area N62 style. This will be the same seating console as is used on the N62. Vinyl cushions and FRP table included. |
| |
|
|
| 15. |
|
Access to F/B from Wheel House thru hinged cockpit hatch custom built by PCM. |
| |
|
|
| 16. |
|
Windows by Pacific Coast Marine with 1/2” (1.27 cm) thick laminated tempered glass
|
| |
A. |
All side windows to be tinted glass |
| |
B. |
Wheel house opening windows x three (3) to be PCM with insect screens |
| |
C. |
All salon windows are recessed 1" (2.5 cm). |
| |
D. |
Galley windows opening PCM |
| |
E. |
Aft wheel house corner windows to be 1/2" (1.27 cm) tempered safety glass. |
| |
|
|
| 17. |
|
Aluminum doors by Pacific Coast Marine as follows (Note: interior as well as exterior PCM doors are included in this schedule): |
| |
A. |
Wheel house--Two (2) ea Weather Tight Dutch door, one (1) L.H. Mortise hinge, one (1) R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm) |
| |
B. |
Salon after--One (1) ea, Weather Tight single opening door. 36" x 73" (91.4 cm x 185.4 cm) |
| |
C. |
Salon port and starboard side--Two (2) ea, Weather Tight Dutch door, R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm) |
| |
D. |
Engine room--One (1) ea, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm). |
| |
E. |
Lazarette--(0ne) 1ea, with port hole, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 46" (53.3 cm x 116.8 cm) |
| |
F. |
Bilge bulkhead between station 2-3, and bulkhead at station 1, two (2) ea Water Tight doors, R.H. surface mount hinge. No paint. |
| |
|
|
| 18. |
|
Boarding Doors: port and starboard - opening in two (2) pieces. Top to fold up and over and bottom to open outboard. Stern door on starboard side aft. Doors to have Freeman "blind" dog lock/handles. |
| |
|
|
| 19. |
|
Davit Marquipt 2500 LB capacity hydraulic/240VAC with extendable boom to 18 feet (5.5m) mounted on fore deck. Davit sized and positioned to launch dinghies from port and starboard side. |
| |
|
|
| 20 |
|
Aft Deck Exterior Cabinet |
| |
A. |
Sink: S/S to drain directly overboard |
| |
B. |
Faucet: Shurflo #133-0210-CP |
| |
C. |
Control alcove for DDEC engine control ABT bow and stern thruster jog levers, rudder angle indicator and steering jog, start/stop, air horn push buttons and forward windlass control |
| |
|
|
| 21. |
|
Bottom Treatment: Three (3) layers of epoxy barrier coat and three (3) coats of anti fouling paint |
| |
A. |
Two (2) coats of antifouling to be applied at Ta Shing and one (1) coat to be applied after the boat is hauled out at Kaohsiung before shipment |
| |
|
|
| 22. |
|
Upper Deck to Drain through six (6) 2" (5.1 cm) scuppers three (3) per side and eight (8) freeing ports four (4 )per side |
| |
|
|
| 23. |
|
Anchor Well to Drain through scupper 2" (5.1 cm) diameter |
| |
|
|
| 24. |
|
All Exterior Lockers to have FRP louvers. |
| |
|
|
| 25. |
|
FRP Exhaust Stack / Radar Mast with flag halyards port and starboard. Stack to have FRP louvers |
| |
|
|
| 26. |
|
Portuguese Bridge Control Stations port and starboard side of forward P/B. Station is recessed into P/B with DDEC control, bow and stern thruster controls, start/stop/horn. Recess to have courtesy light inside. |
| |
|
|
| 27. |
|
Flybridge with FRP Hardtop, sink, U-Line #CO2175FFS drinks refrigerator with Ta Shing made FRP door, and two (2) Stidds "Slimline" helm chairs #500n-2x2 white vinyl and settee with vinyl cushions and high gloss teak table. Sink to drain directly overboard. Ritchie #SS 5000 compass installed. |
| |
A. |
FRP hardtop finished with smooth Gelcoat, with white non-skid |
| |
B. |
Hardtop to have a stainless rail continuation of the ladder on the topside of the hardtop to allow a person to easily access this area. |
| |
C. |
Flybridge to have four (4) freeing ports, two (2) port and two (2) starboard |
| |
|
|
| 28. |
|
Stern Capstan Winches: Two (2) Maxwell VC 2200 24v port and starboard |
| |
|
|
| 29. |
|
Teak Flag Staff 48" (121.9 cm) with socket for aft cap rail |
| |
|
|
| 30. |
|
Door to Foredeck through Portuguese bridge with freeman dog set |
| |
|
|
| 31. |
|
Freeman Watertight Deck Hatch over chain locker, #18HAALR x two (2) |
| |
|
|
| 32. |
|
Anchor: Aritex 300 lb. (136 kg) stainless steel plow x two (2) |
| |
|
|
| 33. |
|
800 ft. 1/2" HT Chain (243.8 m 1.27 cm) in two (2) 400 ft. (121.9 cm) lengths from port and starboard chain lockers |
| |
|
|
| 34. |
|
Swim Ladder: Stainless steel with teak steps mounted on swim step under FRP hatch |
| |
|
|
| 35. |
|
Two (2) Pop-up Style 10" Cleats (25.4 cm) on swim step port and starboard for dinghy tie up |
| |
|
|
| 36 |
|
Windlass: Maxwell VWC 4500 hydraulic with band brake and 1/2" HT (1.27 cm) chain gypsy x two (2) |
| |
|
|
| 37. |
|
Maxwell Chain Stopper for 1/2" (1.27 cm) diameter HT chain x two (2) |
| |
|
|
| 38. |
|
All Exterior Locker Doors to use "Perko" fig. 777 flush hatch dogs as latch |
| |
|
|
| 39 |
|
FRP Louvered Vents on all exterior locker doors |
| |
|
|
| 40 |
|
All Exterior Door Keepers to be ABI #2039CH |
| |
|
|
| 41 |
|
Two (2) Fishing Pole Holders flushed into bulwarks in cockpit. One (1) each port and starboard sides with drains |
| |
|
|
| 42 |
|
Stainless Breast Plate with two (2) anchor wash nozzles and Nordhavn emblem |
| |
|
|
| 43 |
|
Large Pad Eye at stem through boot top 1-1/4" (3.2 cm) OD |
| |
|
|
| 44 |
|
Life Raft Pads port and starboard side of upper deck |
| |
|
|
| 45 |
|
Four (4) "U" Shaped Rails across swim step |
| |
|
|
| 46 |
|
Nordhavn Name Plates x two (2) port and starboard side. |
| |
|
|
| 47 |
|
All Deck Washes to be installed in recessed Ta Shing made FRP boxes with FRP doors. |
| |
|
|
| 48 |
|
Foredeck Lockers, three total: two (2) flush style port and stbd. One centerline fwd of Portuguese Bridge. Centerline locker to have gas shocks to hold open. |
| |
|
|
| 49 |
|
80 Gallon (303 liter) Gasoline Storage Tank with electric pump installed inside Portuguese bridge and accessed from foredeck deck. |
| |
|
|
| 50 |
|
"Flopper Stopper" System for use at anchor. System to include folding poles P&S with associated rigging and two (2) Prime "wing" type flopper plates. |
| |
|
|
| 51 |
|
Zincs |
| |
A. |
Ship loose two (2) left hand shaft zincs and two (2) right hand shaft zincs |
| |
B |
Ship Loose four (4) B4 plate zincs |
| |
|
|
| 52 |
|
Marquipt Dinghy Ladder |
