| 1. |
|
Water Tanks |
| |
A. |
Number and capacity: One (1) tank totaling 600 gallons (2271 liters) |
| |
B. |
Material: Fiberglass from male molds with FDA approved gel coated interior |
| |
C. |
Inspection plates: Appropriately positioned and sized for access |
| |
D. |
Tanks air tested to 4.5 pounds per sq. inch (31005 sq. mm) |
| |
E. |
Each tank to have "Wema" level gauge |
| |
F. |
Each tank to be fitted with sight gauge |
| |
G. |
Tank baffles to be spaced on 24" (61 cm) centers |
| |
H. |
Exterior of tanks finished in blue gel coat |
| |
I. |
Tanks to comply with ABYC section H-23 for potable water systems for use on boats |
| |
J. |
Cleanliness: Tank interior surfaces to be thoroughly vacuumed and wiped down prior to final closure |
| |
K. |
All hoses and cables running through watertight bulkheads to be ran through Roxtec and Ta Shing designed watertight fittings. |
| |
|
|
| 2. |
|
Fuel Tanks |
| |
A. |
Number and capacity: Five (5) main tanks totaling 3950 gallons (14952 liters) with one centerline aluminum “Day Tank” at 80 gallons (303 liters) which will gravity feed from main wing tanks |
| |
B. |
FRP construction from male molds using Vinyl ester resin. To comply with all ABYC codes for diesel fuel tanks. Tanks to be coated with fire retardant Gelcoat on outside to comply with ABYC section H-33.20 for fire resistance per PAE's design. |
| |
C. |
Inspection Plates appropriately positioned for interior access by average size man. Plates to be fitted with labels that contain all information as stated in ABYC section H-33.16.3. Each internal baffle to have a removable panel to allow access to entire interior of all fuel tanks. |
| |
D. |
Fuel system to include a powder coated aluminum supply reservoir, which feeds by gravity from all 5 fuel tanks. a light and audible alarm in wheelhouse if excessive water is present. Reservoir fitted with five (5) draw spigots for main, 2 generators, wing engine and spare - mounted at lower level of reservoir but above water sensing probe. All returns from main, wing and generator plumbed into reservoir via a return manifold. |
| |
E. |
Sight gauges provided for 2 of the 5 fuel tanks |
| |
F. |
Each tank to be air tested to 4.5 pounds per sq. inch (31005 sq. mm) |
| |
G. |
Provide baffles on 24" (61 cm) centers |
| |
H. |
Transfer manifold and 3.5gpm fuel pump with timer switch and Racor 1000 fuel filter with 10 micron element which can transfer fuel from one tank to another and scrub fuel while transferring. |
| |
I. |
Exterior of tanks finished in red gel coat |
| |
J. |
Cleanliness: tank interior surfaces to be vacuumed and wiped clean before final closure |
| |
K. |
Each tank to have two (2) 1” (2.5 cm) I.D. vent lines |
| |
L. |
Each tank to have separate 2” (5.1 cm) I.D. fill pipe located a minimum distance of 18” (45.7 cm) from any ventilation openings. |
| |
M. |
All hardware that comes in contact with fuel to be bonded into the 24vdc ground system |
| |
|
|
| 3. |
|
Fuel Pipe and Hose |
| |
A. |
Supply lines from tanks to supply reservoir are 1-1/2” (3.8 cm) ID with Aeroquip brand fuel hose and swaged brass fittings |
| |
B. |
Fuel line from supply reservoir to main engine filter is 3/4" (19 mm) ID with Aeroquip brand fuel hose and swaged brass fittings |
| |
C. |
Fuel lines from supply reservoir to generator and wing engine to be 1/2” (12.7 mm) ID with Aeroquip brand fuel hose and swaged fittings |
| |
D. |
Vent lines to be fuel certified, reinforced hose 1” (2.5 cm) ID |
| |
|
|
| 4 |
|
Water Hoses |
| |
A. |
Cold water: Hose from water tanks to water pump should be reinforced suction rated hose. Hose from pump to accumulator should be pressure rated reinforced hose. Branch lines to be 1/2" (12.7 mm) Shurflo semi-rigid tubing (blue). |
| |
B. |
Hot water: Shurflo 1/2" (12.7 mm) semi rigid tubing (red) |
| |
C. |
Sea water hoses: Reinforced for marine use and provided with double stainless steel clamps below the water line |
| |
D. |
All hoses used shall meet the requirements for service as set out by ABYC for the system intended |
| |
|
|
| 5 |
|
Heater: RHEEM Vanguard Low Boy, 47 gallon (178 liter) with dual 240VAC elements for quick recovery |
| |
|
|
| 6 |
|
Thru Hulls: Bronze body, S/S Balls and Teflon seats |
| |
A. |
Grounding wire: #6 gauge green wire |
| |
B. |
Each thru hull to have a clearly visible tag indicating use. |
| |
C. |
Each thru hull to be easily accessible |
| |
|
|
| 7 |
|
Fresh Water System |
| |
A. |
Main Pump: Headhunter Mach 5 Model #M5-120/60 - 120V with pressure regulator and Groco WSA-1000 strainer on pump inlet |
| |
B. |
Groco #PST5 accumulator tank with pressure gauge |
| |
C. |
Hose from water tanks to water pumps and to accumulator to be 1" (2.5 cm) diameter reinforced and approved for potable water |
| |
D. |
Back up Pump: Head hunter "X-Caliber" 12-24 VDC pump Model # XR-124 |
| |
E. |
Filter: US water filter housing with a 5 micron sediment filter installed downstream of fresh water discharge manifold |
| |
F. |
Pump Selection Manifolds (2): Pump inlet and discharge manifolds made of stainless steel standard pipe. Supply manifold furnished with isolation ball valves from each fresh water tank, to each fresh water pump, and from the water maker. Discharge manifold furnished with isolation valves from each pump. |
| |
|
|
| 8 |
|
Plumbing Fixtures |
| |
A. |
Head sinks - Six (6) total: Owner's x 2, salon day head , guest lowers, and wheel house. HCG white sinks |
| |
B. |
Galley sink: Double S/S Kohler |
| |
C. |
Head faucets: Six (6) total Grohe Model# 33413-0000 chrome |
| |
D. |
Galley sink faucet: Grohe Model# 32999 1 K0 chrome/black |
| |
E. |
Engine room sink faucet, local stainless steel |
| |
F. |
Engine room sink, fly bridge and aft deck sink: local made stainless steel |
| |
G. |
Shower fixtures: Four (4) All Grohe #28179 handle, #28631 soap dish, #28.620 24" shower bar, #28.151 hose, #34.436 thermostat valve |
| |
H. |
Bath tub owner's head: Local made Jacuzzi tub |
| |
I. |
Tub faucet: Local made |
| |
|
|
| 9 |
|
Shower and Sink Sump Pump System for lower level guest heads and laundry |
| |
A. |
Two FRP drain basins, approximately 5 gallon (18.9 liter) capacity installed below sole of lower level guest heads. Basin to have a bolted flange top cover, separate 1-1/2" (3.8 cm) drain inlets from the head sink and shower stall, a 3/4" (1.9 cm) bottom outlet to the discharge pump, a float switch, and a 3/4" (1.9 cm) overflow to the engine room bilge. |
| |
B. |
Two (2) Whale Gulpers 220, 24volt #IM BP 1554. Pump to auto start by float switch actuation and discharge to the gray water tank. Pump discharge to be equipped with a swing check valve. |
| |
|
|
| 10 |
|
Bilge Pumps |
| |
A. |
Electric: Five (5) Par Jabsco 34600-0010 24volt 10.8 GPM (40.9 LPM) Diaphragm 1" (2.5 cm) diameter ports, with "Ultra Senior" 24volt auto float switch #UPS-01-24/32. One (1) in each water tight compartment. |
| |
B. |
Manual: Five (5) Edson Model #638 AL. One in each water tight compartment. |
| |
C. |
Hydraulic drive emergency pump: One (1) "Pacer" 180 GPM (681 LPM) plumbed to all water tight compartments. Manifold for emergency pump to be located in easily accessible location. |
| |
D. |
High Water Bilge Pump System - Engine Room: RULE Model 16A, 3700 GPH (14006 LPH), 24 VAC, RULE Model #33AL High Water Bilge Alarm, and "Ultra Senior" bilge switch |
| |
E. |
High Water Bilge Alarm Panel - Pilot House High water bilge sense will come from std. Ultra Senior in each bilge compartment. Visual and audio alarm panel in pilot house. |
| |
|
|
| 11 |
|
Toilets and Holding Tank System |
| |
A |
All toilets, five (5) total, to be Tecma Silent Plus |
| |
B |
Water supply to toilets to be fresh water only |
| |
C |
Holding Tank: One (1) FRP 150 gallon (568 liter) holding tank |
| |
D |
Use only PVC pipe or Trident "Odor Safe" hose |
| |
E |
Holding tank overboard pumps: Edson "Bone Dry" #120ELB 20GPM 120/208-230VAC electric and Edson "Bone Dry" #557BR 30GPM manual pump |
| |
F |
Holding tank vent to use Sealand# 310002 vent filter |
| |
G |
Deck fitting for portable evacuation facility |
| |
H |
Holding Tank Level Monitor: Sealand 24V Tank Watch 4 Panel/Tank Master Panel and Cap with Vent, 45 inch (114.3 cm) probes Part #600115, including Universal Flange, 3 inch NPT (7.6 c, NPT) with gasket and stainless steel hardware, 24 volt |
| |
I |
Install Tecma 2 button marine wall switch in each head |
| |
J. |
Install "Do Not Flush" panel at every toilet |
| |
K. |
Black water hoses to Trident #102 hose |
| |
|
|
| 12 |
|
Fresh Water Outlets on the foredeck, aft deck, flybridge and one (1) in engine room using stainless steel spigots. |
| |
|
|
| 13 |
|
Gray Water System |
| |
A. |
Tank: One (1) FRP 150 gallon (568 liter) tank. All sinks, showers, and air conditioning condensate to drain to tank. All drains to have "P" traps and sloped down hill run to tank. Exception: lower level head sink and shower and engine room sink drains will be pumped to gray water tank with Whale "Gulper" pump. Tank equipped with electric and manual discharge pumps, level switch for pump starting, and level monitor system. |
| |
B. |
Electric Discharge Pump: Sealand T24 Discharge Pump. Pump inlet to draw with 1" (2.5 cm) of the absolute bottom of the tank. Pump to discharge overboard through anti siphon loop. |
| |
C. |
Level Monitor System: Sealand 24V Tank Watch 4 Panel/Tank Master Panel and Cap with Vent, 45 inch (114.3 cm) probes part #600115, including Universal Flange (3-inch NPT) (7.6 cm NPT) with gasket and stainless steel hardware |
| |
D. |
Manual back up pump: Edson Model #638AL |
| |
E. |
"Hepvo" odor valve on the gray water system before tank |
| |
|
|
| 14 |
|
Transom Shower "Scandvik" #101513-MR |
| |
|
|
| 15 |
|
LPG System with two (2) 30 lb. aluminum LPG bottles with "Trident" two stage regulator and "Xintex" monitor panel #XINTX#S-2A with two (2) sniffers |
| |
|
|
| 16 |
|
Bosch Washing Machine #WAS 24460UC and 240vac Bosch Dryer #WTV 76100US located in Laundry room on lower level |
| |
|
|
| 17 |
|
Individual Raw Water Inlet thru hulls per item requiring raw water |
| |
A. |
Wing engine, generator(s), water maker intake and air conditioning |
| |
B. |
Each inlet to have Groco strainer |
| |
C. |
Each thru hull on the exterior to have grate installed to keep debris out. |
| |
|
|
| 18 |
|
Oil Change System |
| |
A. |
System utilizes a 120VAC Oberdorfer Gear Pump Model #OBN993M-F36-RC (4.8 GPM) to drain and fill engine lube oil from/to crankcases of main, wing, and generator(s) engines. Pump is controlled by a three (3) position switch mounted at pump location. Switch positions to be labeled "ENGINE OIL DRAIN", "OFF", "ENGINE OIL FILL". |
| |
B. |
Manifold, pump and control switch to be located in an accessible and comfortable location. Engine side of manifold to include isolation valves for each engine. Pump discharge/fill side to include a hose of suitable length for drawing from and discharging to a locally placed container. |
| |
|
|
| 19 |
|
All Pumps and Motors to be mounted on starboard and PVC pads |
