Welcome to Nordhavn.com - Power Thats Oceans Apart
   
 
side_menu



EXTERIOR, DECK HARDWARE AND EQUIPMENT

 

All horizontal surfaces on deck have a diamond pattern non-skid as shown in deck plan.  Standard non-skid to be a contrasting color to parameter deck

 

Chocks for mooring lines:

Transom: Stainless steel with attached cleat - recessed x one (1)

Transom sides: Stainless steel with attached cleat x two  (2)

Amidships: Stainless steel bollard x two (2)

Bow: Stainless steel bollard x two (2)

 

Lower and upper rub rails fiberglass with a light weight 1 1/2" stainless steel cap - rub rails integral to hull

rub rail 1.PNG

 

Stainless steel and FRP double bow roller plank to accommodate up to a 110 lb. (50 kg) anchor on starboard roller and the port roller designed for a second light anchor or for mooring lines.  Starboard side roller slotted for chain and the port roller smooth for handling line

 

Stainless steel stanchions and rails around foredeck to be 1-1/4" (2.86 cm) diameter.  Pulpit 1-1/4" (2.86 cm) diameter with 1" (2.5 cm) socket for burgee staff, 2" dia. SS supports for boat deck

a. Upper rail is tubing with stainless steel life lines below to save weight.

b. Boarding gates port and starboard side of aft deck

 

Windlass: Muir “Jaguar” model #MHR350024E horizontal 3500lbs. windlass mounted on molded fiberglass base. All necessary electrical components to be included. Foot switch mounted near windlass

muir 2.jpg

 

Foredeck hatches: Two (2) Lewmar #30 on FRP boss over laundry and guest head. One (1) Lewmar 60 over fwd guest cabin

               Lewmar 30.jpg lewmar 60.gif

 

 

 

 

 

 

 

 

 

 

Oceanaire privacy/screens for all hatches

oceanaire privacy.PNG

Oceanaire screen 1.PNG

 

 

Windshield wipers - Imtra consisting of:

Coastal Plus 2-speed #RC533222 with auto park x two (2)

#RC538624 Standard pendulum arm  19" -24" , fixed tip x two (2)

#RC520922,  22" blade x two (2)

#EX2134 single wiper rotary switches x two (2)

#EX-SV1/4-24V solenoid valve for wash system x one (1)

#EX21000.326 wash jet x two (2)

#EX2129 elbow (2) #EX2157 interior tubing x 10' (3 m)

#EX2154 exterior tubing x 6' (1.8 m)

All other necessary fittings to make system function properly

4 wipers 1.PNG

4 wipers 2.PNG

 

Windows, port lights and doors:

Wheel house, and salon windows to be .39" (10 mm) tempered glass (high impact resistant glass). Frameless glue in style with "fritted" tinted glass. Forward wheel house windows to be non-tinted. Use "Sika Flex" sealant or equivalent approved system. Curved corner windows to be non-tinted. Windows to meet CE Category A requirements

Salon stbd side door: Hinged Aritex painted Dutch door. Keeper to hold in open position. To meet CE category A requirements for water tightness and scantlings

Aft Salon door:  Aritex stainless steel frame sliding door. Keeper to hold in open position. To meet CE category A requirements for water tightness and scantlings

Engine room door  - L FRP shaped door same style located in aft lower cockpit port side. Stainless steel ladder to access E/R to meet CE Category A requirements for water tightness and scantlings.

Five (5) x 8" diameter opening round stainless steel port holes in hull with screens and dead lights

Four (4) x 8" diameter opening round stainless steel port holes in cabin trunk side fwd with screens and dead lights

Six (6) x glue in hull windows approx. 34" x 10"

One (1) 12" diameter opening round SS with screens at galley.

Two (2)  8" diameter opening port holes on either side of the engine room companionway

 

Transom door: Opens outboard with blind dog set.

 

Boat deck rail to be 1-1/8" (2.86 cm) diameter with life lines below

 

Engine room hatch to have gas shocks to hold open

Stainless steel ladder from deck into E/R.

Provide stainless steel slide bolt lock.

 

Stainless steel telescoping swim ladder mounted on the underside of the swimstep

 

Fly bridge:

FRP double helm seat with fore and aft seating, storage below

L-shaped settees on port and starboard sides with top loading plastic access hatches.

Light weight FRP table at aft side of double helm seat

Stainless and FRP ladder from F/B to lower aft deck

Helm station with helm pump and 18" dia. stainless steel wheel, engine and  thruster controls, engine gauges and start, stop, horn switches 110v ac outlet behind weather proof cover.

Stainless steel and acrylic venturi.

venturi.PNG

FRP radar arch with inspection plates and two (2) Imtra "Ventura" L.E.D. lights. Painted aluminum light tower mounted to back of arch at center line to accommodate the anchor light and wind instruments.

Cushions with Sunbrella fabric

Doors to access area fwd of dash. Port and starboard

 

Davit: Steelhead Marine WD Series model no. #WD600 600 lb. lifting capacity with 8' reach, 355 deg. manual rotation. Stand pipe installation. 

Steelhead 1.PNG

 

All handrails shown on profile drawing and deck plan to be included as standard. Including U rails on swim step

 

Varnish cockpit aft rail x 8 coats

caprail.PNG

 

All deck drains to be 2" diameter on F/B deck, Lower aft deck, side decks and anchor platform

 

Freeing port with flaps in lower aft cockpit one (1) per side

 

 

 

48" teak flag staff with stainless steel socket

flag staff.PNG

Foredeck sun pad with Sunbrella fabric over closed cell foam


*Specifications subject to change without notice and at the discretion of designers and builders.
**Dimensions are subject to change with Buyer’s selected options and personal effects which may add to displacement and increase both draft and waterline length

Last updated: 7/14/14
 


Nordhavn Fleet

40

43

52

56MS

59CP

60

63

64

68

72

75EYF

76

78

96

120