Welcome to Nordhavn.com - Power Thats Oceans Apart

Exterior Deck Hardware

All horizontal surfaces on deck to have Gibco non-skid pattern as shown in deck plan - standard non skid to be a contrasting color to parameter deck

Stainless 316 handrails 1-1/4" (3.2 cm) diameter with electro-polished bases. All rails shown on PAE drawings to be standard in addition to those specified

Transom hand rails

Hand rails along port and starboard side deck coamings

Rail on underside of aft deck overhang

Rail around flybridge sink console

Rail at stairs going up from side deck to Portuguese bridge

Stainless steel 316 Hawse fittings: Four (4) starboard side and three (3) port side per drawing 5" x 10" (12.7 cm x 25.4 cm) with cleats. Recessed into bulwarks where possible. One (1) on aft center line with cleat

Bollard: Aritex # A251Type 400 S/S 316 bollard, one (1) centerline aft of windlass per drawing

Upper rub rail cap to be 316 stainless steel 2-1/2" w x 7/16" thick (6.4 cm w x 1.1 cm thick) fastened with flush 316 stainless steel fasteners. Stainless steel caps on upper and lower rub rails as shown in design

Lower rub rail cap to be 316 stainless steel 1-1/2" w x 5/16" thick (3.8 cmwW x 7 mm thick)

Manship stainless steel oval ports in hull and deck as shown on design. Ports positioned as follows:

Four (4) starboard side hull 8" x 16" (20.3 cm x 40.6 cm) oval

Four (4) port side of hull 8" x 16" (20.3 cm x 40.6 cm) oval

All opening ports to be fitted with screens and deadlights

Storage garage - one (1)

All lower level port lights will be fixed (non-opening)

Stainless steel 316 double bow roller - rollers to be slotted for chain. Roller to be built per PAE design

Stainless steel 316 bow pulpit, rails and stanchions to be 1-1/4" (3.2 cm) diameter. Bow pulpit to have socket for 1" (2.5 cm) burgee staff. Bases to be round with fastening stud welded on bottom, except upper deck which will be fastened with flat head screw

Foredeck to have solid 316 stainless rail with lifeline in middle section. Lifeline to be 5/16" (7 mm) diameter 1 x 19 stainless steel wire without vinyl coating, with 1-1/4" (3.2 cm) diameter stanchions. Bases to be round with fastening stud welded on bottom. All bases to have drain holes on bottom

Windshield Wipers: "Exalto" four (4) 2-speed self-parking motor, with wash system for four (4) front windows

Horn: Kahlenberg dual trumpet # DO-A 24 volt compressor/tank kit # P449-4 and 24 volt solenoid valve kit # V-69-K located on top of stack

Deck hatches: Per deck plan, four (4) Lewmar: Two (2) x # 60 "Ocean Series" and two (2) x # 70 "Ocean Series" to include ocean air insect and privacy screens

Access to flybridge from wheel house through PCM door/hatch

Windows to be Pacific Coast Marine with 1/2” (1.27 cm) thick tempered glass

All side windows to be tinted glass

Three wheel house opening windows to be Pacific Coast Marine with insect screens. Port side starboard side and port aft

All salon windows to be recessed 1" (2.5 cm)

Aluminum doors by Pacific Coast Marine as follows (Note: interior as well as exterior PCM doors are included in this schedule):

Wheel house - Two (2) each, "Weather Tight" Dutch door, one (1) left hand mortise hinge, one (1) right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.3 cm)

Salon aft - one (1) each, "Weather Tight" double door, main opening on left side, mortise hinges. C.O. 48" x 73" (121.9 cm x 185.4 cm)

Salon starboard side - one (1) each, "Weather Tight" Dutch door, right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Salon port side - one (1) each, "Weather Tight" Dutch door, right hand mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Engine room -one (1) each, water tight # PCM4170-W with sound blanket core, painted. Right hand surface mount hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Lazarette - one (1) each, with port hole, "Water Tight"# PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 46" (53.3 cm x 116.8 cm)

Storage garage on starboard side

Boarding doors: port and starboard - opening in two pieces. Top to fold up and over and bottom to open outboard. Stern doors per drawing. Doors to have Aritex stainless steel "blind" dog lock/handles

Davit: 2500 lb. (1134 kg) capacity hydraulic standpipe davit with boom extension from 10' to 14' (3 m-4.3 m)

Aft deck exterior cabinet

Sink: stainless steel to drain directly overboard

Faucet: Aft deck faucet is folding faucet. "Scandvik" # MR4550

Control alcove for engine control ABT bow and stern thruster jog levers, start/stop, air horn push buttons and forward windlass control

Settee with vinyl cushions and three (3) free standing teak chairs

Ladder to boat deck

Console on port side for storage

Bottom treatment: Three (3) layers of epoxy barrier coat and three (3) coats of anti fouling paint

Upper deck to drain through scuppers 2" (5.08 cm) diameter

Anchor well to drain through scupper 2" (5.08 cm) diameter

Port and starboard storage lockers in Portuguese bridge

FRP exhaust stack/radar mast with flag halyards port and starboard per PAE design

Portuguese bridge control stations port and starboard side of forward Portuguese bridge. Station to be recessed into Portuguese bridge with enough room for DDEC control, bow and stern thruster controls, start/stop and horn. Recess to have courtesy light inside

Flybridge per PAE design, sink, Norcold #DE0751 drinks refrigerator, and one (1) Stidd "Slimline" helm chair # 500N-2x2 white vinyl and settee with vinyl cushions and FRP table. Sink to drain directly overboard. Ritchie SS 5000 compass installed

Stern capstan winch: One (1) Maxwell VC 2500 24 volt per PAE design

Flag staff: 48" (122 cm) teak flag staff with socket for aft cap rail

Door to foredeck through Portuguese bridge with Aritex stainless steel dog set

Anchor: 300 lb. (136 kg) stainless steel plow

Chain: 400' of 1/2" HT (122 m of 1.27 cm HT) chain

Swim ladder: Stainless steel with teak steps mounted on swim step

Cleats: Two (2) pop-up style 10" (25.4 cm) cleats on swim step port and starboard for dinghy tie up

Windlass: Maxwell VWC 4500 hydraulic with band brake and 1/2" (1.27 cm) HT chain gypsy

Maxwell chain stopper for 1/2" (1.27 cm) diameter HT chain

All exterior locker doors to use stainless steel flush latches

All exterior locker doors to have FRP louvered vents

All exterior door keepers to be ABI # 2039CH

Two (2) Fishing pole holders flushed into bulwarks in cockpit. One each port and starboard sides with drains

Stainless steel stem plate with anchor wash nozzle and Nordhavn emblem

Large pad eye at stem through boot top

Three (3) "U" shaped rails across swim step

Nordhavn name plates x two (2) port and starboard side per PAE design

40 Gallon (151.42 liter) gasoline storage tank with electric pump installed in a FRP box on the upper deck

"Flopper Stopper" system for use at anchor. System to include folding poles port and starboard with associated rigging and two Prime "wing" type flopper plates

*Specifications subject to change without notice and at the discretion of designers and builders.
**Dimensions are subject to change with Buyer’s selected options and personal effects which may add to displacement and increase both draft and waterline length

Last updated: 7/16/12



Nordhavn Fleet