All Horizontal Surfaces on Deck to have a diamond pattern non skid as shown in deck plan - standard non skid to be a contrasting color to parameter deck

Lower Aft Deck and Side Decks to have 1/2" (1.27 cm) thick teak overlay

316 Stainless Handrails 1-1/4" (3.2 cm) diameter with electro polished bases

N57 style transom hand rails

N57 style hand rails along port and starboard side deck coamings

N57 style rail on underside of aft deck overhang

Rail around F/B sink console

Rails: 41" (104.1 cm) rails at stairs going up from side deck to P/B to be recessed

Vertical handrail on the port and starboard boarding doors

Nine (9) 316 Stainless Steel Hawse Fittings: Eight (8) port and starboard per drawing 5" x 10" (12.7 cm x 25.4 cm) with solid S/S cleats. Recessed into bulwarks where possible. One (1) on aft center line with cleat (Cleats to be solid stainless steel bar)

Two (2) 316 Stainless Steel Bollards centerline aft of windlass

Upper Rub Rail Cap to be 316 stainless steel 2-1/2" W x 7/16" thick (6.35 cm W x 1.11 cm thick) fastened with flush 316 stainless steel fasteners. Stainless steel caps on upper and lower rub rails as shown in design

Lower Rub Rail Cap to be 316 stainless steel 1-1/2" W x 5/16" thick (3.8 cm W x 7.94 mm thick)

Manship Ports in Hull and Deck. Ports positioned as follows

Seven (7) starboard side hull 8" x 16" (20.32 cm x 40.6 cm) oval (3 opening and 4 fixed)

Six (6) port side of hull 8" x 16" (20.32 cm x 40.6 cm) oval (2 opening and 4 fixed)

All opening ports to be fitted with screens and deadlights

316 Stainless Steel Double Bow Roller - rollers to be slotted for chain. Roller to be built per PAE design

316 Stainless Steel Bow and Stern Pulpits and stanchions to be 1-1/4" (3.2 cm) diameter. Bow pulpit to have socket for 1" (2.5 cm) burgee staff. Bases to be round with fastening stud welded on bottom, except upper deck which will be fastened with flat head screw

Foredeck to have solid 316 stainless rail with lifeline in middle section. Bases to be round with fastening stud welded on bottom. All bases to have drain holes on bottom

Windshield Wipers: "Exalto" 2-speed self-parking motor, with wash system for five (5) front windows

#EX2167.32 wiper motor 223BS 24 volt/23Nm, for 1-3/8” (34.5 mm) bulkheads x five (5)

#EX2133 T1 Pantograph arm 10.6" -17.7" (270-450 mm) adjustable x five (5)

#EX2171 curved wiper blade 16" (40.6 cm) x five (5)

#EX2159 Combo switch for single wiper 24 volt x five (5) (custom engraved panel per PAE design)

#EX2143 24 voltolt solenoid valve for wash system x one (1)

#EX2133.03 tubing retainer strip x five (5)

#EX2184 Washing Jet for type 1 adjustable pantograph arm x five (5)

#EX2186 plastic bulkhead connector for 19.7" (50 cm) - new style

#EX2154 Tubing 1/4” (6.35 mm) soft black x 16' (5 m)

#EX2157 Tubing 1/4" (6.35 mm) hard black for push fit plumbing fittings x 16' (5 m)

#EX2129 elbow .24" (6 mm) x six (6)

#EX2166 T-coupling .24x.24x.24" (6x6x6mm) x four (4)

#EX2119 straight coupling , 1/4” (6.35 mm) x one (1)

Horn: Kahlenberg dual trumpet #D-1 with white finish

Deck Hatches: Per deck plan, one (1) Lewmar #70 "Ocean Series" to include insect and privacy screens. Two (2) Lewmar #50 "Ocean Series" to include insect and privacy screens

Dorade Vents: Two (2) to have FRP box with standard TS style 316 SS cowl vent inside painted white and to be positioned per PAE deck plan

Access to Flybridge From Wheel House thru hinged cockpit hatch custom built by PCM

Windows by Pacific Coast Marine with 1/2" (1.27 cm) thick laminated tempered glass

All side windows to be tinted glass

Two wheel house opening windows to be PCM with insect screens

All salon windows to be recessed 1" (2.5 cm)

Aluminum doors by Pacific Coast Marine as follows (Note: interior as well as exterior PCM doors are included in this schedule)

Wheel house - Two (2) each Weather Tight Dutch door. One (1) L.H. Mortise hinge, one (1) R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Salon after - One (1) each Weather Tight Sliding door. 54" x 73" (137.2 cm x 185.4 cm)

Salon starboard side - One (1) each Weather Tight Dutch door, R.H. Mortise hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Engine room - One (1) each, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 73" (53.3 cm x 185.4 cm)

Lazarette - One (1) each, with port hole, Water Tight model no. PCM4170-W with sound blanket core, painted. R.H. surface mount hinge. C.O. 21" x 46" (53.3 cm x 116.8 cm)

Bilge bulkhead between station 2 - 3, and bulkhead at station 1. Two (2) each Water Tight doors, R.H. surface mount hinge. Painted

Please not that the weather tight doors are to have mortise hinges. The watertight doors are to have surface mounted hinges

Boarding Doors: port and starboard - opening in two (2) pieces. Top to fold up and over and bottom to open outboard. Stern door on starboard side aft per drawing. Doors to have Freeman "blind" dog lock/handles

Davit Marquipt2500 lb (1134 kg) capacity hydraulic/240 volt AC davit with extendable boom to 21' (6.4 m) mounted on port aft side of boat deck per drawing. Davit sized and positioned to launch dinghies from port side and stern

Aft deck Exterior Cabinet

Sink: Stainless steel to drain directly overboard

Faucet: Shurflo #133-0210-CP

Control alcove for DDEC engine control ABT bow and stern thruster jog levers, start/stop, air horn push buttons and forward windlass control

Bottom Treatment: Three (3) layers of epoxy barrier coat and three (3) coats of anti fouling paint

Two (2) coats of antifouling to be applied at Ta Shing and one (1) coat to be applied after the boat is hauled out at Kaohsiung before shipment

Upper Deck to Drain through six (6) 2" (5.08 cm) scuppers (3 per side)

Anchor Wellto Drain through scupper 2" (5.08 cm) diameter

Port and Starboard Storage Lockers in Portuguese bridge with FRP louvers

FRP Exhaust Stack/Radar Mast with flag halyards port and starboard

Portuguese Bridge Control Stations port and starboard side of forward Portuguese Bridge. Station to be recessed into Portuguese Bridge as on N57 with DDEC control, bow and stern thruster controls, start/stop/horn. Recess to have courtesy light inside

Flybridge with FRP Hardtop, sink, U-Line #CO2175FFS drinks refrigerator, and two (2) Stidd "Slimline" helm chairs #500n-2x2 white vinyl and settee with vinyl cushions and high gloss teak table. Sink to drain directly overboard. Ritchie #SS 5000 compass installed on FRP pad

FRP hardtop finished with smooth Gelcoat, With white non-skid

Hardtop to have a stainless rail continuation of the ladder on the topside of the hardtop to allow a person to easily access this area

Flybridge to have four (4) freeing ports (2 port and 2 starboard)

Stern Capstan Winches: Two (2) Maxwell VC 2200 24 volt port and starboard

Flag Staff: 48" (121.9 cm) with socket for aft cap rail

Door to Foredeck through Portuguese bridge with freeman dog set

Freeman Watertight Deck Hatch over chain locker, #18HAALR x two (2)

Anchor: Airtex 300 lb. (136 kg) stainless steel Plow x two (2)

Chain: 800' - 1/2" HT Chain (243.8 m - 1.27 cm) in two (2) 400' (121.9 m) lengths from port and starboard chain lockers

Swim Ladder: Stainless steel with teak steps mounted on swim step under an FRP hatch

Cleats: Two (2) Pop-up Style 10" (25.4 cm) Cleatson swim step port and starboard for dinghy tie up

Windlass: Maxwell VWC 4500 hydraulic with band brake and 1/2" (1.27 cm) HT chain gypsy x two (2)

Maxwell Chain Stopper for 1/2" (1.27 cm) diameter HT chain x two (2)

All Exterior Locker Doors to use "Perko" fig. 777 flush hatch dogs as latch

All Exterior Locker Doors to have FRP louvered vents

All Exterior Door Keepers to be ABI #2039CH

Two (2) Fishing Pole Holders flushed into bulwarks in cockpit. One (1) each port and starboard sides with drains

Stainless Steel Breast Plate with two (2) anchor wash nozzles and Nordhavn emblem

Large Pad Eye at stem through boot top 1-1/4" (3.2 cm) O.D

Life Ring Port and Starboard Side of wheel house in recess

Four (4) "U" Shaped Rails across swim step

Nordhavn Name Plates: One (1) each port and starboard side per PAE design

All Deck Washes to be installed in recessed FRP boxes with FRP doors

Foredeck Lockers, Three (3) total: two (2) flush style port and starboard and one (1) on centerline fwd. of P/B. Centerline locker to have gas shocks to hold open

Gasoline Storage Tank 80 Gallon (303 liter) with electric pump installed in a FRP box on the upper deck

"Flopper Stopper" System for use at anchor. System to include folding poles port and starboard with associated rigging and two (2) Prime "wing" type flopper plates

Zincs

Ship loose two (2) left hand shaft zincs and two (2) right hand shaft zincs

Ship Loose four (4) B4 plate zincs

Marquipt Dinghy Ladder